HOW TO CONFIGURE SISCO WITH NETSIM

MEMBERI NAMA SWITCH
=====================

ketik sintak (hostname <spasi> <Nama_Switch>:
contoh :
switch>en
switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
switch(config)#hostname SWITCH_1
SWITCH_1(config)#exit

MEMBUAT PASSWORD BIASA
======================

Sintak yang digunakan (enable password <spasi> <passwordnya>:
contoh :
SWITCH_1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SWITCH_1(config)#enable password 28711
SWITCH_1(config)#exit

MEMBUAT PASSWORD LOGIN SWITCH
=============================
Password ini ditampilkan saat pertama kali kita membuka Hyper_terminal.
1. ketik (line console 0)
2. Ketik passwordnya
3. Ketik (login)
4. Exit


contoh :
SWITCH_1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SWITCH_1(config)#line console 0
SWITCH_1(config-line)#password IMAM
SWITCH_1(config-line)#login
SWITCH_1(config-line)#
SWITCH_1#exit

MEMBUAT PASSWORD TERINSKRIPSI
=============================

Sintak yang digunakan (enable secret <spasi> <passwordnya>:
(ingat .... jangan sampai password terinskripsi sama dengan password biasa).

contoh :
SWITCH_1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SWITCH_1(config)#enable secret IMAM
SWITCH_1(config)#exit

4. Melihat hasil proses yang baru dibuat, sintak yang digunakan (show run):
contoh :
SWITCH_1#sh run
hasilnya .....
Building Configuration...


enable secret 5 $1$rkIO$XsaEE7Q3KCgFAaGqZM/nR.
enable password 28711

HASIL/TAMPILAN KONFIGURASI PASSWORD DIATAS ADALAH :
===================================================

======================================================
= User Access Verification =
= =
= Password: // PASSWORD LOGINNYA =
= =
= SWITCH_1>en // SINTAK MULAI MENGKONFIGURASI =
= Password: // PASSWORD TERINSKRIPSI =
= SWITCH_1# =
======================================================


MENGKONFIGURASI IP ADDRESS PADA SWITCH
========================================

1. Mengkonfigurasi Vlan 1 terlebih dahulu, sintak yang digunakan (interface vlan 1) :
2. Masukkan IP dan SUBMASKnya, sintak yang digunakan (ip address <IP> <spasi> <SUBMASAK>) :
3. Aktifkan port swith, sintak yang digunakan (no shut) :


contoh :
SWITCH_1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SWITCH_1(config)#interface vlan 1
SWITCH_1(config-if)#ip address 192.168.010.034 255.255.255.240
SWITCH_1(config-if)#no shut
SWITCH_1(config-if)#
SWITCH_1#sh run // untuk melihat perubahan konfigurasi.

KONFIGURASI VLAN PADA SWITCH
============================
1. Ketik vlan <vlan ke..>
2. int rang fa0../ .. - ....
3. switchport access vlan >vlan ke ..>
4. switchport mode access
5. exit

contoh :
SWITCH_1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SWITCH_1(config)#vlan 1
SWITCH_1(config-vlan)#int range fa0/1 - 6
SWITCH_1(config-if-range)#switchport access vlan 1
SWITCH_1(config-if-range)#switchport mode access
SWITCH_1(config-if-range)#
SWITCH_1#exit
SWITCH_1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SWITCH_1(config)#vlan 2
SWITCH_1(config-vlan)#int range fa0/7 - 12
SWITCH_1(config-if-range)#switchport access vlan 2
SWITCH_1(config-if-range)#switchport mode access
SWITCH_1(config-if-range)#
SWITCH_1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SWITCH_1(config)#vlan 3
SWITCH_1(config-vlan)#int range fa0/13 - 18
SWITCH_1(config-if-range)#switchport access vlan 3
SWITCH_1(config-if-range)#switchport mode access
SWITCH_1(config-if-range)#
SWITCH_1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SWITCH_1(config)#vlan 4
SWITCH_1(config-vlan)#int range fa0/19 - 24
SWITCH_1(config-if-range)#switchport access vlan 4
SWITCH_1(config-if-range)#switchport mode access
SWITCH_1(config-if-range)#
SWITCH_1#exit


UNTUK MELIHAT HASILNYA
======================

SWITCH_1#sh vlan
ATAU MENGGUNAKAN SINTAK
SWITCH_1#sh run


MEMBERI IP PADA ROUTER
======================
IMAM#conf t
Enter configuration commands, one per line. End with CNTL/Z.
IMAM(config)#int fa0/0.1
IMAM(config-subif)#encapsulation dot1q 1
(** NetSim Warning: On some routers you must do this BEFORE setting an IP Address **)
IMAM(config-subif)#ip address 192.168.010.017 255.255.255.240
IMAM(config-subif)#no shut
IMAM(config-subif)#
IMAM#exit

Spoiler:

mantaaap...
kami nanti postingan selanjutnya mas..

Aw.. Aw.. Aw.. mnnnstabb..